Vista 20p Indicates Bell Failure What to Do to Get the Bell to Sound Again
Where is the VISTA-20P Bong Supervision?
Supervision of the bong excursion wiring has evolved over the life of the Vista-20P Panel. In early on versions, bong supervision was always enabled. The manner of supervision could be changed by cutting a jumper and installing a resistor. Afterward versions allowed bong supervision to be disabled.
In revisions one - 5 of the Vista- 20P Panels, bell supervision is always enabled. Out of the box, the alarm panel supervises the bell circuit for a short, or for reversed polarity. If either of these weather condition were to occur, a Bong Failure (Blastoff Keypad) or a Check lxx (Fixed Keypad) error would be displayed.
To supervise for either a brusk or an open up circuit on the bong output, power down the panel, cut the cerise jumper indicated on the schematic and install the provided 2K resistor in parallel on the concluding sounder in the circuit. A trouble condition on the bell excursion is always treated as a problem, even if the system is armed when it occurs. Information technology will non prevent the user from arming the system:
In panel revision 7, the ability to enable or disable bell supervision was added to the Vista-20P Panel. If bell supervision is not desired, information technology tin be disabled through programming location *91.
If bell supervision is desired, enable it in *91. Additionally, ability downward, cut the bell supervision jumper on the circuit board and install the provided 2K resistor. If a curt or an open occurs on the bell circuit when supervision is enabled, a Bell Failure (Alpha Keypad) or Check 70 (Stock-still Keypad) will be displayed. Bong Failure volition always exist treated as a trouble, even when the system is armed. It will not foreclose the user from arming the system.
In panel revision 9, the process for supervising the bong output was streamlined. In this version, if you desire to supervise the bell wiring for an open or a short circuit, you must enable bell supervision processing in *91. Y'all must likewise install the supplied 820 Ohm resistor in parallel beyond the last sounder in line. An open or a brusk on the bell excursion volition cause a Bong Failure (Alpha Keypad) or a Check seventy (Fixed Keypad). These situations will ever be treated as trouble conditions. A Bong Failure will non prevent a user from arming the system.
Complete the following steps to enable bell supervision:
- Connect the resistor to the siren- The resistor must exist continued to the positive and negative terminals on the siren. These are the same terminals that will be used to connect the siren to the Vista-20P Panel. Install one leg of the resistor on the positive concluding and one leg on the negative final. Too brand sure to install the wire connecting the siren to the system on these terminals. Brand a note which wire is going to which final.
- Connect the siren to the system- The siren connects to terminals 3 and four on the alert panel. Last 3 is positive, and terminal 4 is negative.
- Enable Bong Supervision in programming- Bell supervision must exist enabled in system programming. At a keypad enter your installer code (default is 4112) + [viii] + [00]. You lot will see "Installer Code xx" or just "xx" depending on the type of keypad being used. Enter [*91] plus the appropriate entry. Remember, you will need to add the digits for all the features you wish to enable here. For example, if y'all desire to enable Bell Supervision and Exit Delay Restart/Reset, you will enter a ix. If you need to enter a 2-digit number, such as 13 (all options enabled), enter [#] + [13].
In panels with revision 9.12 and 9.18, in that location is a 2nd entry in this field for enabling RIS (remote interactive services) for Full Connect two.0. To enable it, enter a 2 in the 2nd digit entry of this field.
Once you lot have filled in the field, you lot will hear a triple beep, and the keypad will advance automatically to the next field in programming. Press *99 to exit programming.
Did yous find this respond useful?
We offer alarm monitoring every bit low equally $10 / month
Click Here to Learn More
Related Products
Altronix RBSNTTL
Ultra Sensitive Relay Module
Listing Cost: $28.00
Our Toll: $ 18 . 99
Related Categories
- DIY Wired Security Systems
- 2GIG 345MHz Sensors
- Power Supplies
- Answered
- Answered Past
Source: https://www.alarmgrid.com/faq/where-is-the-vista-20p-bell-supervision
0 Response to "Vista 20p Indicates Bell Failure What to Do to Get the Bell to Sound Again"
Postar um comentário